CUPLOCK SCAFFOLDING MANUAL PDF

User Manual Cuplok () – Download as PDF File .pdf), Text File .txt) or read online. User Guide SGB Cuplock Scaffold System. Uploaded by. S. GUIDANCE NOTE. This manual is valid only for the use of. Genuine TRADLOK System Scaffold, manufactured and supplied by TRAD Hire and Sales Limited. This document is subject to periodic revision and updating. Before designing scaffolds with. Systems™ Scaffold components, visit to be.

Author: Dogami Moogule
Country: Singapore
Language: English (Spanish)
Genre: Relationship
Published (Last): 9 July 2012
Pages: 336
PDF File Size: 6.30 Mb
ePub File Size: 7.5 Mb
ISBN: 637-9-78824-224-2
Downloads: 70592
Price: Free* [*Free Regsitration Required]
Uploader: Bakasa

Tianjin Tianyingtai ringlock ledger end with high quality. Guidance Note For this heavier duty and in particular when new equipment is supplied, it will greatly assist in the striking of the falsework if the top screw jacks are lubricated. Horizontals to be checked for level.

cuplock scaffolding manual

Horizontal forces have to include wind forces, the effect of eccentricity, and out of plumb as per BS. These are identified by a colour flash and four lug cups. Special Cases Every effort should be made to comply with the rules scaffoldin ties wherever possible. If exposed to high winds, stability checks must be made. The galvanized surface makes scaffolding plank more stronger in the rainy days and moist environment.

Help Center Find new research papers in: Jacks at the head and base level may be loaded to values shown below provided they are fully and effectively braced against horizontal loads.

Scaffold Boards on top and nailed down if gap between adjacent decks exceeds regulations. The rules for bracing must be observed. For conventional Formwork the max.

The maximum Safe Working Axial Loads of the braces in tension or compression depends on the type of brace used. Jack extension is a variable on manusl graphs and curves are given for horizontal forces of 0, 1, 2, 2. Bottom jack extension unbraced and bottom lift. Curved scaffolds can be constructed by using a combination of rectangular and trapezium shaped bays Scaffold Type A in the following pages or from all trapezium shaped bays Scaffold Type B. Sample Order Free samples. Where jack bracing is necessary, it should be made using the details shown in these diagrams.

  AS BRUMAS DE AVALON VOL 4 PDF

The bracing adaptor allows lacing with Cuplok horizontals.

Alternative, jack bracing can be used at the base, see pages and for details. When the 1m cantilever frames are used cupllck the end point load is 7.

The diameters shown in the table on page are those which just touch the inside face of the inside horizontal. The basis of design is usually that the buckling length is between the horizontal lifts.

However, they may be used in cantilever form as shown, in corners only, provided that the loads shown on pages 31 and 32 are not exceeded. For braced scaffolds all base and top jacks must be effectively diagonally braced in both directions. If braces are terminated within the structure the vertical component force must be added to all other vertical forces and the total must not exceed the loads stated.

Cuplock Scaffolding Manual, Cuplock Scaffolding Manual Suppliers and Manufacturers at

The extension of the jack is max. The falsework structure must be 4 or more bays long in both directions. This is achieved by firstly erecting the forkheads to the approximate level required. The bracing can be provided externally, i. The supplier supports Trade Assurance — A free service that protects your orders from payment to delivery. The direction of the braces must be alternated. Cuplock Scaffolding Standard Welding Machine. They may be made up as shown.

  MADAN MUSINGS 01 06 PDF

However, occasionally it is not possible to secure the tie to the structure and the following special procedure should be adopted. Primary and secondary timbers for a small part of the formwork area are placed in position.

Scaffolding Checklist Scaffold Safety Checklist.

CUPLOK Data Sheets | Ramakrishnan Sundaram –

It is preferable that braces in adjacent panels should also be alternated in direction, as shown by the dashed lines in the diagram. If the formwork is continuous and with rigid connections between members, then forkhead lacing should not be required.

The resultant figure is the additional vertical load on the verticals where the diagonal bracing terminates and may act either upwards or downwards. Guidance Notes When it is required to provide a sscaffolding of Access Scaffold, which is curved in plan, such as to give access to the inside or outside of circular tanks, etc.

Galvanized steel pipe galvanized scaffolding ringlock ladder bracket made in China. Hop – Up Brackets The rules for hop – up brackets, are the same as for straight runs. The use of Swivel Couplers for bracing should be avoided wherever possible and the use of the SGB Right-angle Mark 3A Coupler is recommened, because of its higher load carrying capacity.

The amount of diagonal bracing required should be calculated, but a minimum of one brace for every 7 bays, in every row, in both directions is required.